Networks test

 0    400 карточки    tobiaszblach
скачать mp3 Печать играть Проверьте себя
 
Вопрос English Ответ English
What is the Protocol Data Unit (PDU) at Layer 1 of the OSI model?
начать обучение
Bit
Which of the following transmission media belong to the category of guided media?
начать обучение
Twisted pair, coaxial cable, and fiber optic
Why is differential signaling used in Ethernet?
начать обучение
To cancel external electromagnetic interference by subtracting the two opposing signals at the receiver
Which duplex mode is described by the classic walkie-talkie principle?
начать обучение
Half-duplex
What is the main problem with NRZ-L (Non-Return-to-Zero Level) encoding when transmitting long runs of identical bits?
начать обучение
Long runs of the same bit produce no signal transitions, causing the receiver to lose clock synchronization
Which encoding scheme does 100BASE-TX use, and what efficiency does it achieve?
начать обучение
4B/5B with MLT-3, 80% efficiency
How many discrete voltage levels does PAM-5 use, as employed in 1000BASE-T (Gigabit Ethernet)?
начать обучение
5 levels (−2, −1, 0, +1, +2)
What does the abbreviation BASE mean in Ethernet designations such as 10BASE-T?
начать обучение
Baseband transmission — the entire cable carries a single digital signal
A noise-free channel has a bandwidth of 5 MHz and uses PAM-4 (4 signal levels). What is the maximum data rate according to the Nyquist theorem?
начать обучение
20 Mbit/s
What does the Shannon-Hartley theorem describe?
начать обучение
The absolute theoretical upper limit of the data rate on a noisy channel, regardless of the encoding scheme used
What is the maximum supported data rate of Cat5e cables?
начать обучение
1 Gbit/s
What is the maximum reach of Cat6 at 10 Gbit/s, and why is Cat6A superior?
начать обучение
Cat6 only reaches 55 m at 10G; Cat6A achieves
How much power does the PoE standard IEEE 802.3at (PoE+) deliver to the powered device (PD)?
начать обучение
25.5 W
IEEE 802.3bt Type 4 delivers up to 71.3 W. Which cable category is recommended for long PoE runs, and why?
начать обучение
Cat6A or cables with larger conductor cross-sections, to minimize resistive losses over long distances
Why can PoE (Power over Ethernet) not be transmitted over fiber optic cables?
начать обучение
Fiber is an electrical insulator (glass) and cannot conduct electric current
What is the core diameter of single-mode fiber (SMF), and what does this enable?
начать обучение
8–9 µm, allowing only one light mode and enabling distances of 80 km or more
Why must APC connectors (8° angled) never be mated with UPC connectors (flat-polished)?
начать обучение
The angular mismatch creates an air gap that physically damages both ferrules and causes high insertion loss
A new 10 Gbit/s copper run of 80 m is planned (no EMI, limited budget). Which cable category is correct?
начать обучение
Cat6A — supports 10GBASE-T up to
What is the maximum allowed untwist length when terminating Cat6A cables at an RJ45 connector?
начать обучение
Approximately 6 mm
In NRZI (Non-Return-to-Zero Inverted) encoding, how is a binary 1 represented on the wire?
начать обучение
A transition (level change) occurs at the start of the bit period
What signaling scheme does 100BASE-TX place on the wire after 4B/5B block coding?
начать обучение
MLT-3 (Multi-Level Transmit, three levels)
Why does 4B/5B coding map 4 data bits onto 5-bit code words?
начать обучение
The redundant codes guarantee enough transitions (no more than three consecutive zeros) for clock recovery
What is the main purpose of scrambling a bit stream before transmission?
начать обучение
To randomize the data so long runs of identical bits are broken up, aiding clock recovery and reducing spectral peaks
Differential Manchester encoding signals a binary 0 by
начать обучение
a transition at the start of the bit period (the mandatory mid-bit transition is always present)
Why does MLT-3 reduce the dominant signal frequency compared to binary NRZI at the same bit rate?
начать обучение
It takes four bit periods to complete one full waveform cycle, so the fundamental frequency is about one quarter of the bit rate
Which Ethernet standard uses Manchester encoding on the wire?
начать обучение
10BASE-T
A channel has a bandwidth of 4 kHz and uses 4 signal levels. What is the Nyquist capacity? C = 2 · B · log2(L).
начать обучение
16,000 bit/s
Using the Nyquist formula C = 2 · B · log2(L), how many signal levels are required to reach 24 kbit/s over a 3 kHz channel?
начать обучение
16 levels
A channel has B = 1 MHz and a linear SNR of 3. What is the approximate Shannon capacity? C = B · log2(1 + SNR).
начать обучение
2 Mbit/s
A 10 MHz channel has an SNR of 20 dB. What is the approximate Shannon capacity? (20 dB = linear 100.)
начать обучение
About 66.6 Mbit/s
Bandwidth and data rate are related but distinct. Which statement is correct?
начать обучение
Bandwidth is a frequency range in Hz; for a fixed bandwidth the data rate rises by using more signal levels or higher SNR
A −10 dB change in power corresponds to which multiplier?
начать обучение
× 0.1 (one tenth)
What does 0 dBm represent in absolute terms?
начать обучение
1 milliwatt
Differential signaling cancels external noise because
начать обучение
the same interference is induced on both wires and the receiver outputs the difference (A − B), removing the common component
Which duplex mode transmits in one direction only, such as a broadcast TV signal?
начать обучение
Simplex
Cat6 cable is specified to what frequency bandwidth?
начать обучение
250 MHz
Cat8 cable is specified to which bandwidth, and what is its maximum reach?
начать обучение
2,000 MHz, with a maximum reach of about 30 m
A standard twisted-pair data cable contains how many pairs, and why are the pairs twisted at different rates?
начать обучение
Four pairs; different twist rates reduce crosstalk between the pairs
Why must shielded cabling be properly grounded at the appropriate point(s)?
начать обучение
Improper grounding can let the shield act as an antenna and worsen performance instead of improving it
FEXT (Far-End Crosstalk) is distinguished from NEXT by
начать обучение
being measured at the far end of the link, where the disturbing signal has also attenuated
Why is alien crosstalk the key barrier that Cat6A addresses for 10GBASE-T over 100 m?
начать обучение
Because 10 Gbit/s uses all pairs in both directions, and AXT from neighboring cables cannot be cancelled by the receiver; Cat6A's design and shielding suppress it
What limits the distance and bandwidth of multimode fiber compared to single-mode?
начать обучение
Modal dispersion, as different light paths (modes) arrive at slightly different times
Which fiber wavelength is associated with the C-band used for long-haul single-mode transmission and lowest attenuation?
начать обучение
1550 nm
The ST fiber connector is characterized by which coupling mechanism?
начать обучение
A bayonet twist-lock
By color code, an APC connector body is typically which color, and UPC which color?
начать обучение
APC is green; UPC is blue
IEEE 802.3bt Type 4 (PoE++) delivers what power at the PSE, and what is available at the powered device?
начать обучение
Up to 90 W at the PSE, with about 71.3 W available at the PD
What does the "BASE" in standards like 100BASE-TX and 1000BASE-T denote?
начать обучение
Baseband signaling, where the medium carries a single digital signal occupying the full bandwidth
How many pairs does 1000BASE-T use, and in what manner?
начать обучение
All 4 pairs, each carrying data bidirectionally and simultaneously with echo cancellation
What is the baud (symbol) rate of 100BASE-TX on the wire?
начать обучение
125 MBd
Which Ethernet copper standard requires Cat6A to reliably reach 100 m?
начать обучение
10GBASE-T
What is the chief disadvantage of Manchester encoding that motivated its replacement at 100 Mbit/s?
начать обучение
It needs twice the bandwidth of the bit rate (only 50 percent efficient)
Which statement about clock recovery and line coding is correct?
начать обучение
A good line code guarantees frequent transitions so the receiver can continuously recover and lock its clock to the data
What is the Protocol Data Unit (PDU) at Layer 2 of the OSI model?
начать обучение
Frame
What is the main function of the LLC sublayer (Logical Link Control, IEEE 802.2)?
начать обучение
Protocol multiplexing: identifying the Layer 3 protocol (IP, ARP, IPv6) carried in the frame
What do the first 3 bytes (24 bits) of a MAC address encode?
начать обучение
The OUI (Organizationally Unique Identifier) — the manufacturer identifier assigned by the IEEE
What does I/G bit = 1 in the first byte of a MAC address indicate?
начать обучение
The address is a multicast or broadcast address (group address)
Which MAC address is the universal broadcast address, and which protocols typically use it?
начать обучение
FF: FF: FF: FF: FF: FF — used by ARP requests and DHCP Discover, among others
An Ethernet frame contains EtherType 0x0806. Which Layer 3 protocol is in the payload?
начать обучение
ARP (Address Resolution Protocol)
Why is the minimum Ethernet frame size 64 bytes?
начать обучение
Due to the legacy CSMA/CD mechanism: a frame had to be long enough so that it was still being transmitted when the collision signal returned from the far end of the cable
What does the MTU (Maximum Transmission Unit) define in standard Ethernet, and how does it differ from the total frame size?
начать обучение
The MTU is 1500 bytes (payload only); the total frame size is up to 1518 bytes (Preamble/SFD are outside the counted frame)
What can CRC-32 (Frame Check Sequence) do, and what can it NOT do?
начать обучение
CRC-32 can detect errors but NOT correct them; corrupted frames are silently discarded, and correction is handled by higher-layer protocols such as TCP
What is the function of the preamble (7 bytes) in an Ethernet frame?
начать обучение
It is an alternating 1-0 pattern that allows the receiver to synchronize its clock to the incoming signal frequency before the actual data arrives
What is the fundamental difference between a hub (Layer 1) and a switch (Layer 2) regarding collision domains?
начать обучение
A hub forms one large shared collision domain for all ports; a switch creates a separate collision domain per port (full-duplex, no collisions)
What does a switch do when it receives a frame destined for a MAC address that is not in its CAM table?
начать обучение
It floods the frame to all ports except the ingress port (unknown unicast flooding)
Why can devices in different VLANs not communicate directly at Layer 2?
начать обучение
VLANs create separate broadcast domains; a Layer 3 device (router or L3 switch) is required for inter-VLAN communication
Which EtherType value does an 802.1Q VLAN tag use in an Ethernet frame?
начать обучение
0x8100
How long does convergence take in classic STP (802.1D), and what is the operational consequence?
начать обучение
Approximately 30–50 seconds; this represents a significant outage during topology changes
Host A (192.168.1.10) wants to send a frame to Host B (192.168.1.20) but does not know its MAC address. Which ARP sequence is correct?
начать обучение
Host A broadcasts an ARP Request to FF: FF: FF: FF: FF: FF; only Host B replies with a unicast ARP Reply containing its MAC address; Host A caches the mapping in its ARP table
What is a Gratuitous ARP, and for which legitimate purposes is it used?
начать обучение
An unsolicited ARP Reply in which a device announces its own IP-to-MAC mapping; used at boot time, during failover, and to detect IP address conflicts
Which of the four core functions of the Data Link Layer is responsible for organizing a raw stream of bits into structured units before transmission?
начать обучение
Framing
How many total bits and bytes make up a standard MAC address?
начать обучение
48 bits (6 bytes)
When the I/G bit (bit 0 of the first byte) of a MAC address is 0, the address is:
начать обучение
A unicast address (a single, individual device)
The Logical Link Control (LLC) sublayer is defined by which IEEE standard?
начать обучение
IEEE 802.2
In an Ethernet II frame, how large is the EtherType field?
начать обучение
2 bytes
What is the valid payload size range of a standard Ethernet II frame?
начать обучение
46 to 1500 bytes
An end station receives an Ethernet frame with EtherType 0x0800. Which protocol does the payload contain?
начать обучение
IPv4
How large is the Preamble in an Ethernet frame, and what is its purpose?
начать обучение
7 bytes of alternating 1-0 pattern used for receiver clock synchronization
What is the standard Ethernet MTU, and what does it count?
начать обучение
1500 bytes, counting the payload only
A station needs to send a payload of only 20 bytes. What happens to satisfy the minimum frame size?
начать обучение
The payload is padded up to 46 bytes so the total frame reaches 64 bytes
Which of the following is NOT something CRC-32 can detect?
начать обучение
It cannot correct any errors it finds
What is the typical default aging timer for entries in a switch CAM table?
начать обучение
300 seconds (5 minutes)
In a CAM table overflow attack, the attacker floods the switch with many random source MAC addresses. What is the result?
начать обучение
The CAM table fills up and the switch falls back to flooding all frames, allowing the attacker to sniff traffic
At which OSI layer does a hub operate, and how does it handle an incoming frame?
начать обучение
Layer 1; it repeats the signal out of all other ports regardless of destination
A bridge and a switch are functionally related. Which statement best describes their relationship?
начать обучение
A switch is essentially a multiport bridge implemented in hardware; both operate at Layer 2 and learn MAC addresses
The 64-byte minimum Ethernet frame size is fundamentally tied to which mechanism?
начать обучение
CSMA/CD collision detection — the frame must still be transmitting when a collision signal could return from the far end
In an 802.1Q tag, what is the value of the TPID field that identifies the frame as VLAN-tagged?
начать обучение
0x8100
What is the function of the 3-bit PCP (Priority Code Point) field in an 802.1Q tag?
начать обучение
It carries a Class of Service (CoS) priority value from 0 to 7 for QoS
On a trunk port, frames belonging to the native VLAN are transmitted in what manner?
начать обучение
Untagged
Two PCs are connected to the same switch but are in VLAN 10 and VLAN 20 respectively. To communicate, what is required?
начать обучение
A Layer 3 device (router or L3 switch) with an interface in each VLAN
Classic STP is defined by which IEEE standard?
начать обучение
IEEE 802.1D
How does STP elect the root bridge?
начать обучение
The switch with the lowest Bridge ID becomes the root bridge
Which destination MAC address is used for STP BPDU (Bridge Protocol Data Unit) frames?
начать обучение
01:80: C2:00:00:00
What is the role of an STP root port on a non-root switch?
начать обучение
It is the port with the lowest path cost toward the root bridge
In which STP port state does a port populate the MAC address table but still not forward user frames?
начать обучение
Learning
Which standard STP path cost corresponds to a 100 Mbps link?
начать обучение
19
How does the target host send its ARP Reply?
начать обучение
As a unicast directly back to the requesting host
What is the typical default timeout for entries in a host's ARP cache?
начать обучение
300 seconds
A user on an access port in VLAN 10 cannot reach a server on the same switch. show vlan brief reveals the server's port is in VLAN 20. What is the cause?
начать обучение
A VLAN mismatch — the two devices are in different broadcast domains and need Layer 3 routing
Two directly connected switch ports show many late collisions and CRC errors, and throughput is poor. show interfaces status hints at a configuration issue. What is the most likely cause?
начать обучение
A duplex mismatch (one side half-duplex, the other full-duplex)
Cut-through switching achieves very low latency because it:
начать обучение
Begins forwarding as soon as the destination MAC is read, without waiting for the full frame or CRC check
Which Layer 2 attack is mitigated by Dynamic ARP Inspection (DAI)?
начать обучение
ARP spoofing (ARP cache poisoning)
Wireshark display filter eth. type == 0x0806 would capture which traffic?
начать обучение
ARP frames only
Link Aggregation (IEEE 802.3ad / LACP) combines multiple physical links. How does it typically distribute traffic?
начать обучение
By hashing fields such as source/destination MAC or IP to select a member link (per-flow)
The destination MAC FF: FF: FF: FF: FF: FF in a frame tells a switch to:
начать обучение
Flood the frame to all ports except the ingress port
An IPv4 address is structured as 32 bits. How are these bits grouped in dotted-decimal notation?
начать обучение
Four octets of 8 bits each, separated by dots
What is the decimal value of the binary octet 00010000?
начать обучение
16
Which 8-bit binary value represents the decimal number 172?
начать обучение
10101100
How many total IPv4 addresses are theoretically possible with 32 bits?
начать обучение
4,294,967,296 (2^32)
Which IPv4 address class is reserved for multicast?
начать обучение
Class D (224
Which CIDR prefix corresponds to the RFC 1918 private range 172.16.0.0?
начать обучение
/12
What is the full address range covered by the loopback block 127.0.0.0/8?
начать обучение
127.0.0.0
The address block 169.254.0.0/16 is used for which purpose?
начать обучение
Link-Local / APIPA addresses self-assigned when DHCP fails
How many usable host addresses does a /29 subnet provide?
начать обучение
6
How many /28 subnets can be created from a single /24 network?
начать обучение
16
What is the dotted-decimal subnet mask for a /20 prefix?
начать обучение
255.255.240.0
What is the network address of host 10.10.10.130 with a /25 mask?
начать обучение
10.10.10.128
For the subnet 192.168.1.64/26, what are the first and last usable host addresses?
начать обучение
First: 192.168.1.65, Last: 192.168.1.126
Using a /27 mask, what is the block size (number of addresses per subnet)?
начать обучение
32
A point-to-point WAN link needs only 2 usable addresses. Which prefix is the classic choice?
начать обучение
/30
In a VLSM design, after allocating Engineering 10.0.0.0/25 (126 hosts), at which address does the next subnet start?
начать обучение
10.0.0.128
The IHL (Internet Header Length) field holds its minimum value of 5. How many bytes of header does this represent?
начать обучение
20 bytes (5 × 4-byte words)
What is the purpose of the Identification field in the IPv4 header?
начать обучение
It carries the same value for all fragments of one original packet so the destination can group them for reassembly
Which protocol number appears in the IPv4 Protocol field for UDP?
начать обучение
17
The MF (More Fragments) flag is set to 0. What does this indicate?
начать обучение
This is the last fragment (or the packet was not fragmented)
What is the principle behind Path MTU Discovery using the DF flag?
начать обучение
Send packets with DF set; if a router cannot forward without fragmenting it returns an ICMP "fragmentation needed" message, so the sender lowers packet size
What is the correct name for the PDU (Protocol Data Unit) at Layer 3 of the OSI model?
начать обучение
Packet
Why are both MAC addresses (Layer 2) and IP addresses (Layer 3) necessary?
начать обучение
MAC addresses are flat and non-hierarchical (routing is not possible); IP addresses are hierarchical and enable routing.
How many bits does an IPv4 address consist of, and how many possible addresses does that theoretically yield?
начать обучение
32 bits, approximately 4.3 billion addresses (2^32)
What is the decimal value of the binary number 10101100?
начать обучение
172
A host has the IP address 192.168.1.100 with a /24 subnet mask. What is the network portion and what is the host portion?
начать обучение
Network: 192.168.1, Host:
What is the purpose of the 169.254.x. x (APIPA / Link-Local) address range?
начать обучение
It is automatically assigned when a device cannot reach a DHCP server.
Which organization manages IP address allocation in Europe (including Austria)?
начать обучение
RIPE NCC
What was the main advantage of introducing CIDR in 1993 over classful addressing?
начать обучение
CIDR allows flexible prefix lengths (e.g., /22) instead of being restricted to fixed Class A, B, or C sizes, dramatically reducing address waste.
Why are 2 addresses always subtracted from the total number of addresses in a subnet when calculating usable hosts?
начать обучение
Because the network address (all host bits = 0) and the broadcast address (all host bits = 1) cannot be assigned to any device.
What is the broadcast address of the subnet 192.168.1.64/26?
начать обучение
192.168.1.127
What is VLSM (Variable Length Subnet Masking) and why is it used in practice?
начать обучение
VLSM allows different prefix lengths within the same address space, so subnets can be sized precisely for their actual needs (e.g., /25 for
A company needs a subnet for exactly 500 hosts. What is the smallest prefix that meets this requirement?
начать обучение
/23 (510 usable hosts)
How large is an IPv4 header without options, and what is the minimum value of the IHL field?
начать обучение
20 bytes; minimum IHL value = 5 (5 × 4 bytes = 20 bytes)
Where does the reassembly of fragmented IPv4 packets take place?
начать обучение
Exclusively at the destination host — never at intermediate routers.
What is the function of the default gateway for a host?
начать обучение
It is the IP address of the router interface on the local subnet; the host forwards all packets destined for other networks to this address.
A routing table contains the entries 10.0.0.0/8, 10.50.0.0/16, and 0.0.0.0/0. A packet arrives destined for 10.50.5.1. Which route is used?
начать обучение
10.50.0.0/16, because /16 is the longest matching prefix.
What happens at Layer 2 when a router receives a packet on interface eth0 and forwards it out interface eth1?
начать обучение
The router strips the old Layer 2 header (with the incoming MAC addresses), creates a new Layer 2 header with the appropriate MAC addresses for the next link, and decrements the TTL.
A user reports no internet connectivity. Running ipconfig / ip addr shows the IP address 169.254.15.23. What is the most likely cause?
начать обучение
The device failed to reach a DHCP server and automatically assigned itself an APIPA address (169.254.x.x).
How many bits does an IPv6 address use?
начать обучение
128
In which year was the global IANA IPv4 address pool fully depleted?
начать обучение
2011
How many addresses does the IPv6 address space provide (approximately)?
начать обучение
3.4 × 10^38
What is the standard subnet prefix length for an IPv6 subnet?
начать обучение
/64
IPv6 has no broadcast. What mechanism replaces broadcast functionality?
начать обучение
Multicast
Which IPv6 address type is automatically generated on every interface, never routed beyond the local link, and starts with fe80:?
начать обучение
Link-Local
What is the prefix for IPv6 Global Unicast Addresses (GUA)?
начать обучение
2000:/3
What is the IPv6 loopback address?
начать обучение
:1
The IPv6 header has a fixed size of how many bytes?
начать обучение
40
How many fields does the IPv6 header contain?
начать обучение
8
IPv6 does not include a header checksum.
начать обучение
True
In IPv6, routers can fragment packets if they are too large for a link.
начать обучение
False
The IPv6 "Hop Limit" field serves the same purpose as the IPv4 TTL field.
начать обучение
True
Expand the abbreviated IPv6 address 2001: db8:1 to its full form. Which is correct?
начать обучение
2001:0db8:0000:0000:0000:0000:0000:0001
Why may the: (double colon) appear only once in an IPv6 address?
начать обучение
Using it twice would make the number of replaced zero groups ambiguous
The IPv6 default route covering all destinations is expressed as:
начать обучение
:/0
In practice, which sub-range of the ULA block is actually used because the L bit is set to 1 for locally assigned prefixes?
начать обучение
fd00:/8
Which prefix identifies all IPv6 multicast addresses?
начать обучение
ff00:/8
The solicited-node multicast address used by Neighbor Discovery is formed from which prefix?
начать обучение
ff02:1: ff00:0/104
A GUA (Global Unicast) address typically divides into which three parts?
начать обучение
Global routing prefix, subnet ID, interface ID
Within a /48 site allocation, how many bits remain for the subnet ID before the /64 interface boundary?
начать обучение
16
When pinging a link-local address such as fe80:1, why must the interface (zone ID) be specified, e.g. fe80:1%eth0?
начать обучение
Link-local addresses are not unique across interfaces, so the host must know which link to use
Which of these addresses is a link-local address?
начать обучение
fe80: a1: b2ff: fe03: c4d5
Roughly how many addresses does the 128-bit IPv6 space contain?
начать обучение
About 3.4 × 10^38
Which IPv6 header field is used for QoS / DSCP marking, analogous to the IPv4 Type of Service?
начать обучение
Traffic Class
Which IPv6 header field identifies the type of the next header (upper-layer protocol or extension header)?
начать обучение
Next Header
In the IPv6 Next Header field, which value indicates that UDP follows?
начать обучение
17
Optional IPv6 functionality (fragmentation, source routing, IPsec) is carried in what?
начать обучение
Extension headers chained via the Next Header field
Which Next Header value identifies the Fragment extension header?
начать обучение
44
Because IPv6 routers never fragment, what must the source use to avoid oversized packets?
начать обучение
Path MTU Discovery
Which RFC defines stateless address autoconfiguration (SLAAC)?
начать обучение
RFC 4862
During Duplicate Address Detection, what message does the host send and to which destination?
начать обучение
A Neighbor Solicitation to the solicited-node multicast address
After inserting FFFE, the EUI-64 process flips which bit of the first byte?
начать обучение
The 7th bit (the U/L, universal/local bit)
What privacy problem do Privacy Extensions (RFC 4941) solve?
начать обучение
EUI-64 embeds the MAC address, allowing devices to be tracked across networks
In stateless DHCPv6 (RA flags A=1, O=1), how is the address obtained versus the extra configuration?
начать обучение
The address comes from SLAAC; DHCPv6 supplies extra info such as DNS servers
On which UDP port does a DHCPv6 client listen?
начать обучение
546
Which RFC defines the Neighbor Discovery Protocol (NDP)?
начать обучение
RFC 4861
Which ICMPv6 type number is assigned to the Neighbor Solicitation message?
начать обучение
135
Which NDP message lets a router inform a host of a better next-hop for a destination?
начать обучение
Redirect
What does NAT64 accomplish?
начать обучение
It translates between IPv6 and IPv4 so IPv6-only clients can reach IPv4 servers
Which compressed address is INVALID because it uses: more than once?
начать обучение
2001: db8:1
Which everyday IPv6 functions rely on link-local addresses?
начать обучение
NDP, SLAAC router solicitation/advertisement, and routing-protocol adjacencies
IPv6 routers along the path are allowed to fragment packets that exceed the link MTU.
начать обучение
False
DHCPv6 servers listen on UDP port 546 while clients use 547.
начать обучение
False
IPv6 still includes a header checksum that routers recalculate at each hop.
начать обучение
False
The IPv6 loopback address: 1 is 64 bits long.
начать обучение
False
Neighbor Solicitation messages are sent to the solicited-node multicast address during address resolution and DAD.
начать обучение
True
When abbreviating an IPv6 address, the rule is that: (double colon) can be used to replace the longest consecutive run of all-zero groups. How many times can: appear in a single address?
начать обучение
Once
In SLAAC, a host sends a Router Solicitation to which IPv6 multicast address?
начать обучение
ff02:2 (all routers)
DHCPv6 uses which UDP ports?
начать обучение
546 and
Privacy Extensions (RFC 4941) generate a random Interface ID to prevent
начать обучение
tracking of users across networks via their MAC-derived address
What is the difference between forwarding (data plane) and routing (control plane)?
начать обучение
Forwarding moves individual packets based on the routing table; routing builds and maintains the routing table using protocols
A routing table contains entries for 10.0.0.0/8, 10.1.0.0/16, and 10.1.1.0/24. A packet is destined for 10.1.1.50. Which entry will the router use?
начать обучение
10.1.1.0/24 (most specific match)
To enable IPv4 forwarding on a Linux system, which file must contain the value 1?
начать обучение
/proc/sys/net/ipv4/ip_forward
Static routes added with "ip route add" on Linux are lost after a reboot.
начать обучение
True
What is an Autonomous System (AS)?
начать обучение
A network or group of networks under one administrative authority with a unified routing policy
Which algorithm does OSPF use to calculate the shortest path?
начать обучение
Dijkstra SPF (Shortest Path First)
Which routing protocol uses the DUAL algorithm and supports unequal-cost load balancing?
начать обучение
EIGRP
BGP prevents routing loops by using the
начать обучение
AS-PATH attribute (a route that already contains the local AS is rejected)
PAT (Port Address Translation) allows many private IP addresses to share a single public IP address. What field is used to distinguish the individual connections?
начать обучение
Source port number
CGNAT (Carrier-Grade NAT) uses which reserved address range?
начать обучение
100.64.0.0/10
In a firewall rule set, the principle that "what is not explicitly permitted is denied" is called:
начать обучение
Implicit deny
Which plane of operation is responsible for moving an individual packet from an input interface to an output interface?
начать обучение
The data plane (forwarding)
A Linux route shows "proto kernel scope link src 192.168.1.10". What kind of route is this?
начать обучение
A directly connected route, auto-created when the IP address was assigned to the interface
A routing table has 192.168.0.0/16 and 192.168.4.0/24. A packet for 192.168.9.7 arrives. Which entry is used?
начать обучение
192.168.0.0/16, because 192.168.9.7 does not fall inside 192.168.4.0/24
Which is a genuine disadvantage of static routing?
начать обучение
It does not scale and provides no automatic failover when topology changes
By default, a Linux machine with two NICs in different subnets will NOT route packets between them because
начать обучение
IP forwarding is disabled by default and the packet is silently dropped
A router is a Layer 3 device that
начать обучение
connects different subnets and forwards packets between them based on IP addresses
Which categorisation is correct?
начать обучение
OSPF and IS-IS are link-state IGPs; RIP and EIGRP are distance-vector IGPs; BGP is a path-vector EGP
Which RIP loop-prevention technique stops a router from advertising a route back out the interface on which it was learned?
начать обучение
Split horizon
Which transport protocol and port does RIP use to exchange updates?
начать обучение
UDP port
How does OSPF differ from RIP regarding update behaviour?
начать обучение
OSPF sends updates only when the topology changes, not periodically like RIP
An OSPF Area Border Router (ABR)
начать обучение
connects one or more non-backbone areas to the backbone Area 0
Which protocol uses a composite metric based primarily on bandwidth and delay and guarantees loop-free paths with DUAL?
начать обучение
EIGRP
Which statement about BGP route selection is most accurate?
начать обучение
BGP selects routes based on policy and business relationships, not strictly the shortest path
What is the Administrative Distance of iBGP?
начать обучение
200
Two routing sources advertise the same network: OSPF (AD 110) and EIGRP internal (AD 90). Which route is installed in the routing table?
начать обучение
The EIGRP route, because a lower Administrative Distance is more trusted
Which statement about Static NAT is correct?
начать обучение
It provides a permanent one-to-one mapping between a private and a public IP, allowing inbound access (e.g., to a server)
Approximately how many simultaneous sessions can a single public IP support under PAT, limited by the source-port field?
начать обучение
Around 65,000 (limited by the 16-bit port range)
A major drawback of NAT for certain applications is that it
начать обучение
breaks true end-to-end connectivity, complicating protocols like FTP, SIP/VoIP, and IPsec AH
What is a key consequence of an ISP deploying CGNAT?
начать обучение
It adds a second layer of NAT, so customers share public IPs and inbound connections become harder
Which conntrack state describes the very first packet of a new connection?
начать обучение
NEW
The default-deny (implicit deny) principle means
начать обучение
anything not explicitly permitted by a rule is dropped
In iptables, packets generated by the local host itself traverse which chain?
начать обучение
OUTPUT
Which Linux firewalling framework is the modern successor to iptables, unifying IPv4, IPv6, ARP, and bridge filtering?
начать обучение
nftables
Traceroute reveals the path a packet takes by
начать обучение
sending packets with incrementing TTL values and collecting the ICMP Time Exceeded replies from each hop
In a TCP segment, what does the Acknowledgment Number field actually contain?
начать обучение
The sequence number of the NEXT byte the receiver expects to receive
What is the semantic difference between the PSH and URG flags in TCP?
начать обучение
PSH tells the receiver to deliver buffered data to the application immediately; URG marks a region of the stream (via the Urgent Pointer) as priority out-of-band data
What is the purpose of TCP keepalive probes?
начать обучение
To detect dead peers and keep idle-connection state alive by periodically probing a connection that has had no data for a long time
What problem does Karn's algorithm solve in TCP's RTT estimation?
начать обучение
It excludes RTT samples from retransmitted segments, removing the ambiguity of not knowing whether an ACK matches the original or the retransmission
Why is QUIC 0-RTT data considered vulnerable to replay attacks?
начать обучение
The early data is sent before the full handshake completes using a pre-shared key, so an attacker can capture and resend it; therefore only idempotent requests should be sent as 0-RTT
How many bits is a port number?
начать обучение
16 bits
What is the port range for well-known (system) ports?
начать обучение
0 to 1023
What is the port range for dynamic/ephemeral ports?
начать обучение
49152 to 65535
How many values are used to uniquely identify a TCP connection (the so-called 4-tuple)?
начать обучение
Source IP + source port + destination IP + destination port (4 values)
A web server can handle thousands of simultaneous TCP connections to the same port 443 because:
начать обучение
Each connection has a unique 4-tuple (different source IP and/or source port)
Which "ss" command shows all listening TCP and UDP ports with their owning process?
начать обучение
ss -tulnp
Which well-known port does SSH use?
начать обучение
22
Which well-known port does HTTPS use?
начать обучение
443
Which well-known ports does FTP use for control and data?
начать обучение
21 (control) and 20 (data)
Which well-known port does SMTP Submission (authenticated mail submission) use?
начать обучение
587
Which well-known port does POP3 (unencrypted) use?
начать обучение
110
Which well-known port does IMAP (unencrypted) use?
начать обучение
143
Which well-known port and protocol does DNS primarily use for queries?
начать обучение
53 (UDP and TCP)
Which well-known port does NTP (Network Time Protocol) use?
начать обучение
123 (UDP)
Which well-known port does SNMP Trap use to receive notifications?
начать обучение
162 (UDP)
Which well-known port does LDAP use?
начать обучение
389
Which well-known port does SMB (Windows file sharing) use?
начать обучение
445
Which registered port does PostgreSQL use?
начать обучение
5432
DNS uses TCP instead of UDP in which situation(s)?
начать обучение
Zone transfers and responses larger than
What is the minimum size of a TCP header?
начать обучение
20 bytes
Which IP protocol number is assigned to TCP?
начать обучение
6
Why does TCP use a 3-Way Handshake instead of a 2-Way Handshake?
начать обучение
Both sides need to synchronise independent Initial Sequence Numbers and confirm bidirectional reachability
Why is the Initial Sequence Number (ISN) chosen pseudo-randomly?
начать обучение
To prevent TCP sequence prediction attacks (RFC 6528)
How long does the TIME_WAIT state typically last?
начать обучение
2 × MSL (approximately
Which TCP flag is used to abruptly terminate a connection (no graceful teardown)?
начать обучение
RST
How does TCP detect packet loss using duplicate ACKs (Fast Retransmit)?
начать обучение
After receiving 3 duplicate ACKs (4 ACKs with the same number), retransmit the missing segment immediately
A TCP connection in ESTABLISHED state means:
начать обучение
The 3-Way Handshake is complete and data can flow in both directions
Many connections in SYN_RECEIVED state on a server most likely indicate:
начать обучение
A potential SYN flood attack
What is the size of the UDP header?
начать обучение
8 bytes (fixed)
How many fields does the UDP header contain?
начать обучение
4 (source port, destination port, length, checksum)
Which of the following is NOT a typical reason to choose UDP over TCP?
начать обучение
Guaranteed in-order delivery
Which statement about TCP and broadcast/multicast is correct?
начать обучение
TCP cannot perform broadcast or multicast — it is strictly point-to-point
What does Flow Control protect against, and what mechanism is used?
начать обучение
Protects the receiver from buffer overflow; uses the Receiver Window (rwnd)
During TCP Slow Start, how does the congestion window (cwnd) grow?
начать обучение
Exponentially — it doubles every RTT (starting from 1 MSS)
When TCP detects loss via RTO timeout (no ACKs at all), how does it react?
начать обучение
Resets cwnd to 1 MSS and restarts Slow Start
ECN (Explicit Congestion Notification) allows congestion to be signalled:
начать обучение
By routers marking IP packets instead of dropping them
Which transport protocol does HTTP/3 use?
начать обучение
QUIC over UDP
A "connection refused" error when connecting to a TCP service usually means:
начать обучение
No process is listening on the requested port (the server sent RST)
Which sysctl tweak helps when a server runs out of ephemeral source ports?
начать обучение
Extending the ephemeral port range via net. ipv4. ip_local_port_range
Which HTTP status code is returned when a new resource has been successfully created, for example after a successful POST?
начать обучение
201 Created
What is the key difference between a 307 Temporary Redirect and a classic 302 Found?
начать обучение
307 guarantees the HTTP method (e.g. POST) is preserved on the redirected request, whereas
Which status code tells the client that the resource was deliberately and permanently removed, and will not return (stronger than 404)?
начать обучение
410 Gone
A server is temporarily overloaded or down for maintenance and cannot handle the request right now. Which status code is correct?
начать обучение
503 Service Unavailable
A response includes the header "ETag: "v17-cd23"". On a later request, which header does the client send to ask the server whether the cached copy is still valid?
начать обучение
If-None-Match
What does "Transfer-Encoding: chunked" allow a server to do?
начать обучение
Send the response body in pieces without knowing the total length in advance, omitting Content-Length
What is the primary purpose of the HTTP OPTIONS method?
начать обучение
To discover the communication options (e.g. allowed methods) available for a resource, also used in CORS preflight
During TLS negotiation, which extension lets the client and server agree on the application protocol (e.g. h2 for HTTP/2) within the handshake?
начать обучение
ALPN (Application-Layer Protocol Negotiation)
An SRV record encodes which information for locating a service?
начать обучение
Priority, weight, port and target hostname for a named service
What is "negative caching" in DNS?
начать обучение
Caching the fact that a name does NOT exist (an NXDOMAIN response) for a period defined by the SOA, to avoid repeated failing lookups
Which of the following is NOT a Layer 7 protocol?
начать обучение
TCP
When you type "amazon. de" and press Enter, which step happens FIRST?
начать обучение
DNS resolves the name to an IP address
HTTP is fundamentally based on which communication pattern?
начать обучение
Request and response
In an HTTP request, which line comes first?
начать обучение
The request line (method + path + version)
Which HTTP header tells the server which website the request is for, when multiple sites share one IP?
начать обучение
Host
Which HTTP method is used to READ a resource without modifying it?
начать обучение
GET
Which HTTP method is NEITHER safe NOR idempotent?
начать обучение
POST
An HTTP status code starting with 2xx indicates:
начать обучение
Success
An HTTP status code starting with 4xx indicates:
начать обучение
The client made a mistake
Which status code means "the resource has not been modified, use your cached copy"?
начать обучение
304 Not Modified
What is the precise meaning of HTTP status code 403?
начать обучение
Authenticated, but you are not authorised to access this resource
Which status code is typically returned by a reverse proxy when it cannot reach the backend?
начать обучение
502 Bad Gateway
What is the main performance limitation of HTTP/1.1 that browsers worked around by opening 6 to 8 parallel TCP connections?
начать обучение
Only one request can be in flight per TCP connection at a time
Which feature of QUIC lets an HTTP/3 session survive a Wi-Fi to cellular network switch?
начать обучение
Connection migration (via connection IDs instead of the 4-tuple)
HTTPS is best described as:
начать обучение
HTTP wrapped in a TLS encryption layer
What is the primary purpose of HTTP cookies?
начать обучение
To give HTTP state — for example, to remember that a user is logged in
Which architectural model does nginx primarily use, that makes it efficient for handling many idle connections?
начать обучение
Event-driven with a small number of worker processes
Which API style is the default choice for public APIs and uses JSON over HTTP?
начать обучение
REST
What is the primary function of DNS?
начать обучение
Translate human-readable domain names into IP addresses (and vice versa)
Which symbol represents the DNS root zone?
начать обучение
A single dot (.)
When your browser needs to resolve a domain name, which server does it talk to directly?
начать обучение
Its configured resolver (often the ISP or a public resolver like 1.1.1.1)
Which DNS record type maps a name to an IPv4 address?
начать обучение
A
Which DNS record type defines an alias from one name to another name?
начать обучение
CNAME
Which DNS record type lists the authoritative nameservers for a domain?
начать обучение
NS
Which DNS record type controls which Certificate Authorities are allowed to issue TLS certificates for a domain?
начать обучение
CAA
What does DNSSEC protect against?
начать обучение
Tampering and cache poisoning of DNS answers (integrity)
What is one practical advantage of DoH over DoT?
начать обучение
DoH traffic looks identical to normal HTTPS, making it much harder to block or distinguish on the network
What is the primary defence against DNS cache poisoning attacks?
начать обучение
DNSSEC, combined with randomised source ports and transaction IDs
A standard MTA from 1985 receives a modern MIME message with base64 attachments it cannot interpret. What does it do?
начать обучение
It relays the message unchanged, because MIME lives entirely inside the body and is invisible to SMTP
Why is the LMTP / local pipe used by the MDA (typically port 24) distinct from SMTP relay on port 25?
начать обучение
LMTP delivers to the final mailbox store and returns a separate status per recipient instead of queuing
Which SMTP reply code is returned by QUIT when the server closes the session politely?
начать обучение
221
What is the difference between reply codes 450 and 550 for an unavailable mailbox?
начать обучение
450 is a transient failure (retry later);
The SMTP VRFY command is usually disabled on public servers. Why?
начать обучение
It lets an attacker confirm which addresses exist, leaking valid recipients for spam or attacks
What is the advantage of BDAT (CHUNKING, RFC 3030) over the classic DATA command?
начать обучение
BDAT sends a declared byte count so no dot-stuffing or end-of-data scanning is needed
A receiving MTA does not advertise SMTPUTF8 but a sender tries to use an internationalised (UTF-8) address. What is the correct rejection?
начать обучение
550 5.6.7 Need SMTPUTF8 support
A DSN message is structured using which MIME content type defined by RFC 3464?
начать обучение
multipart/report
What is the primary purpose of the Message-ID: header?
начать обучение
A globally unique, domain-scoped identifier used for threading (In-Reply-To/References) and loop/duplicate detection
Which MIME multipart subtype glues independent parts such as a text body plus separate file attachments?
начать обучение
multipart/mixed
Quoted-printable encoding represents the byte 0xE2 (part of a UTF-8 sequence) on the wire as
начать обучение
#NAZWA?
The internationalised domain münchen. de is stored on the wire (without SMTPUTF8) as which Punycode form?
начать обучение
xn--mnchen-3ya. de
In a DKIM-Signature header, what does the bh= tag contain?
начать обучение
The hash of the canonicalised message body
In a DKIM-Signature, "c=relaxed/relaxed" specifies
начать обучение
the canonicalisation algorithms applied to the header and body before hashing
In a DMARC record, what does the pct= tag control?
начать обучение
The percentage of mail to which the published policy is applied (useful during rollout)
What problem does ARC (Authenticated Received Chain, RFC 8617) solve?
начать обучение
It preserves original SPF/DKIM/DMARC results across forwarders so legitimate forwarded mail is not failed
Which acronym describes the email client a user actually interacts with (Outlook, Thunderbird, Apple Mail)?
начать обучение
MUA — Mail User Agent
Which agent relays mail between domains using DNS MX lookups?
начать обучение
MTA — Mail Transfer Agent
What does it mean that email is "store-and-forward"?
начать обучение
Each MTA accepts the whole message into a queue and only then attempts the next hop
Which addresses constitute the SMTP "envelope" of an email?
начать обучение
MAIL FROM and RCPT TO
Which Content-Transfer-Encoding is best suited for arbitrary binary attachments like PDFs and images?
начать обучение
base64
Which SMTP port is reserved for MTA-to-MTA relay between domains?
начать обучение
25
Which SMTP port provides implicit TLS (encrypted from byte 1) for client submission, re-blessed by RFC 8314?
начать обучение
465
SMTP is best characterised as which kind of protocol?
начать обучение
Stateful, plain-text, line-oriented, command/response over a single TCP connection
An SMTP reply code starting with 5xx means:
начать обучение
Permanent negative — stop, do not retry
Which SMTP command requests the extended capability list (ESMTP)?
начать обучение
EHLO
How does the DATA portion of an SMTP message end?
начать обучение
A line containing only a single dot (CRLF. CRLF)
Which SMTP AUTH mechanism is considered modern and resistant to replay attacks?
начать обучение
SCRAM-SHA-256
When picking among multiple MX records for a domain, which one does the sender try first?
начать обучение
The MX record with the lowest preference number
Which port is used for POP3 with implicit TLS (POP3S)?
начать обучение
995
Why is POP3 mostly considered legacy in 2026?
начать обучение
It cannot natively synchronise folders, flags or read-state across multiple devices
Which port is used for IMAP with implicit TLS (IMAPS)?
начать обучение
993
What is the difference between FETCH BODY[TEXT] and FETCH BODY. PEEK[TEXT]?
начать обучение
BODY[TEXT] implicitly sets the Seen flag; BODY. PEEK[TEXT] retrieves the content without changing any flag
How does a STRIPTLS downgrade attack work against mail submission?
начать обучение
An on-path attacker silently removes the STARTTLS line from the server's EHLO reply, causing the client to fall back to plaintext
What does SPF (RFC 7208) publish?
начать обучение
A list of IP addresses authorised to send mail for a domain (as a DNS TXT record)
Which DMARC policy value tells receivers to monitor only and apply no enforcement?
начать обучение
p=none
Which mechanism preserves SPF, DKIM and DMARC results across mailing-list forwarders that would otherwise break them?
начать обучение
[moodle]ARC — Authenticated Received Chain (RFC 8617)
How many layers does the OSI reference model define?
начать обучение
7
Which OSI layer is closest to the end user?
начать обучение
Layer 7 (Application)
What is the Protocol Data Unit (PDU) at the OSI Transport layer?
начать обучение
Segment
What is the Protocol Data Unit (PDU) at the OSI Data Link layer?
начать обучение
Frame
Which is the correct order of the OSI layers from Layer 1 to Layer 7?
начать обучение
Physical, Data Link, Network, Transport, Session, Presentation, Application
Which OSI layer provides end-to-end data delivery, reliability, and flow control?
начать обучение
Transport layer (Layer 4)
Which OSI layer transmits raw bits over a physical medium?
начать обучение
Physical layer (Layer 1)
Which OSI layer handles data format translation, encryption, and compression?
начать обучение
Presentation layer (Layer 6)
Character encoding such as ASCII and Unicode is a task of which OSI layer?
начать обучение
Presentation layer (Layer 6)
Data compression to reduce the size of transmitted data is performed at which OSI layer?
начать обучение
Presentation layer (Layer 6)
Dialog control and the management of full-duplex, half-duplex, and simplex communication modes is a function of which OSI layer?
начать обучение
Session layer (Layer 5)
Which of the following are listed as examples of Session layer mechanisms?
начать обучение
NetBIOS, RPC, and login sessions
Which of the following is an Application layer protocol used for name resolution?
начать обучение
DNS
SMTP, POP3, and IMAP are Application layer protocols used for which service?
начать обучение
Email
Which Transport layer protocol is connection-oriented and provides reliable delivery?
начать обучение
TCP
Which characteristic best describes UDP compared to TCP?
начать обучение
Low overhead and fast, with no guaranteed delivery
What identifies the application associated with a Transport layer communication?
начать обучение
Port number
At the Network layer, what kind of address identifies a device across networks?
начать обучение
IP address (logical address)
Which protocols operate at the OSI Network layer?
начать обучение
IP, ICMP, OSPF, and BGP
Packet fragmentation, when needed, is handled by which OSI layer?
начать обучение
Network layer (Layer 3)
How does the Data Link layer detect errors in received frames?
начать обучение
Using a Cyclic Redundancy Check (CRC)
Which protocols are associated with the Data Link layer?
начать обучение
Ethernet (802.3) and Wi-Fi (802.11)
Which of the following does the Physical layer define?
начать обучение
Electrical, optical, or radio signals, voltage levels, and signal timing
In the OSI model, the upper layers (5, 6, and 7) are often grouped as which category?
начать обучение
Software layers
How many layers does the TCP/IP model commonly have?
начать обучение
4 (sometimes described as 5)
The TCP/IP Internet layer corresponds to which OSI layer?
начать обучение
Network layer (Layer 3)
The TCP/IP Transport layer corresponds to which OSI layer?
начать обучение
Transport layer (Layer 4)
Which protocols are listed for the TCP/IP Internet layer?
начать обучение
IP, ICMP, and ARP
Which organization is credited with developing the TCP/IP model?
начать обучение
DoD / IETF
In practice, why do engineers still use OSI layer numbers (such as "Layer 3 switch")?
начать обучение
OSI numbers are used to describe concepts, while TCP/IP protocols are used for actual communication
During encapsulation, in what order is the data transformed from the Application layer down to the Physical layer?
начать обучение
Data, Segment, Packet, Frame, Bits
What part of a PDU carries the actual user information rather than control information?
начать обучение
The payload
According to the slides, what does PDU stand for?
начать обучение
Protocol Data Unit
What does PCI (Protocol Control Information) refer to in a layered model?
начать обучение
The header and/or trailer added by each layer
What is a Service Access Point (SAP)?
начать обучение
The interface between adjacent layers
Which device operates at the Physical layer and simply regenerates or repeats signals to all ports?
начать обучение
Hub
A router makes forwarding decisions based on which type of address?
начать обучение
IP address (Layer 3)
A firewall that filters traffic based on IP addresses and TCP/UDP port numbers operates at which OSI layers?
начать обучение
Network and Transport layers (Layers 3 and 4)
Which organization manages Internet standards published as RFCs?
начать обучение
IETF (Internet Engineering Task Force)
Which standards organization is part of the United Nations and focuses on telecommunication standards?
начать обучение
ITU (International Telecommunication Union)
Which RFC defines TCP (Transmission Control Protocol)?
начать обучение
RFC
Which RFC number corresponds to the very first RFC, "Host Software"?
начать обучение
RFC 1
What is the definition of a protocol given in the slides?
начать обучение
The rules for the format, order, and actions of messages exchanged between communicating entities
What is the main reason for using a layered architecture in networking?
начать обучение
Complexity management — breaking a huge problem into smaller, manageable parts
Which benefit of layering means each layer only needs to know the interface of adjacent layers?
начать обучение
Abstraction
A LAN speed is given as "1-10 Gbps" in the slides. What does Gbps measure?
начать обучение
Data rate (gigabits per second)
Bit rate, voltage levels, and signal timing are defined at which OSI layer?
начать обучение
Physical layer (Layer 1)
The Data Link layer adds both a header and a trailer to data from Layer 3. What is the trailer field used for error detection commonly called?
начать обучение
Frame Check Sequence (FCS)
During encapsulation, which layer adds the header that turns "Data" into a "Segment"?
начать обучение
The Transport layer (Layer 4)
A device described as operating at "Layer 3" forwards data based on which information?
начать обучение
Logical IP addresses
When two hosts negotiate, maintain, and gracefully end a logical conversation independent of the underlying transport connection, which OSI layer is conceptually responsible?
начать обучение
Session layer (Layer 5)
In the TCP/IP model, the Session, Presentation, and Application layers of OSI are combined into a single Application layer.
начать обучение
True

Вы должны войти в свой аккаунт чтобы написать комментарий.